Industrial Anti Slip Tape
 | Industrial Anti Slip Tape
|
Product Description
Caution Roll Company is an industrial anti slip tape manufacturer producing abrasive traction tape for factory floors, workshop paths, metal platforms, warehouse walkways, and loading areas. It is made for concrete and steel surfaces where oil mist, fine dust, cleaning moisture, safety boot traffic, and daily wear can reduce grip. The tape creates a rough walking surface on smooth floors, worn steel plates, and dusty access routes where reliable underfoot traction is needed during industrial work.
Product Photos
Technical Data Sheet
Item | Typical Value |
Product Type | Abrasive industrial walkway traction tape |
Backing Material | Flexible PVC film |
Surface Material | Aluminum oxide mineral grit |
Adhesive Type | Solvent acrylic pressure-sensitive adhesive |
Total Thickness | 0.80 +/- 0.10 mm |
Standard Roll Size | 50 mm x 18 m |
Custom Width Range | 25 mm to 600 mm |
Peel Adhesion on Steel | >= 18 N/25 mm after 24 h |
Recommended Application Temperature | 10 C to 40 C |
Service Temperature | -10 C to 70 C |
Recommended Surfaces | Dry concrete, sealed floor, steel, aluminum, painted metal |
Abrasion Check | 1,000 dry footwear rubbing cycles, visible grit retained |
Edge Lift Check | 24 h observation after roller pressure application |
Indoor or Outdoor Use | Indoor and sheltered outdoor use |
Shelf Life | 12 months in original packaging |
Surface Preparation | Dry, clean, degreased, dust-free surface required |
Application
- Used as factory floor grip tape near machine access paths, inspection points, and production walkways.
- Adds abrasive safety tape for walkways in warehouses, maintenance zones, and dusty pedestrian routes.
- Suitable as anti slip tape for platforms, mezzanines, steel decks, equipment access points, and raised work areas.
- Applied on loading dock transitions, trailer access points, ramp edges, and door areas where moisture is common.
- Used in workshop zones near tool benches, repair bays, coolant splash areas, and oily work paths.
- Installed on concrete walkways where dust, powder, cleaning water, or worn sealer can reduce traction.
- Cut into step pads for ladders, service platforms, machinery steps, and narrow industrial access points.
Product Overview
In a factory or workshop, a floor does not need to be visibly wet to become unsafe. Fine dust from cutting, light oil mist near machines, coolant splash, worn floor coating, or repeated safety boot movement can all reduce grip over time. The risk is often highest on narrow walking routes, around tool stations, beside production lines, and at points where workers stop, turn, or carry materials.
Caution Roll Company produces this industrial anti slip tape with a mineral abrasive surface, flexible PVC backing, and pressure-sensitive adhesive. The grit layer gives footwear a rougher contact point, while the backing helps the tape stay stable under regular foot traffic. For production areas that need factory floor grip tape, it can be applied to prepared concrete, sealed floors, painted metal, aluminum, and steel plates.
Metal surfaces need special attention. Steel platforms, tread plates, diamond plates, and loading ramps can become slick from moisture, worn footwear, or surface polishing. For slightly uneven metal surfaces, a more conformable backing can help the tape follow the surface profile and reduce edge lifting.
This product is not made as floor marking tape. High-visibility colors can make step edges or platform zones easier to see, but the main function is traction, not visual zoning.
Benefits
- Adds grip to industrial floors affected by dust, oil film, cleaning water, or worn coatings.
- Works as heavy duty anti slip tape for loading ramps, metal platforms, workshop paths, and high-use walking zones.
- Abrasive grit surface helps resist wear from repeated safety boot traffic, stopping, turning, and pivoting.
- Adhesive bonds well on properly cleaned concrete, sealed floors, painted metal, aluminum, and steel plates.
- Helps reduce edge lift when applied with firm roller pressure on dry, degreased, dust-free surfaces.
- Available in standard rolls, custom widths, and pre-cut pieces for equipment steps or narrow platform areas.
- Typical peel adhesion target on stainless steel can reach 18 N/25 mm after 24 hours at 23 C, depending on adhesive grade and surface preparation.
- Abrasion checks can include 1,000 dry footwear rubbing cycles to review grit retention and visible surface wear.
What Makes Factory Floors Lose Grip During Daily Work?
Factory floors often lose grip little by little. A sealed concrete walkway may feel safe in the morning, then become less reliable after dust, oil mist, coolant splash, cleaning water, and safety boot movement collect through the day. The same issue can happen near machines, loading doors, repair benches, or turning points where workers repeatedly stop and pivot. Industrial anti slip tape adds a controlled abrasive layer to these high-contact areas, helping footwear regain traction where the original floor surface has become too smooth, contaminated, or worn for steady movement.
Warehouse
How Should Concrete and Steel Surfaces Be Prepared Before Application?
Good surface preparation is often the difference between long service life and early edge failure. Concrete should be dry, firm, and free from loose dust, powdering cement, oil residue, wax, weak sealer, or peeling coating. Rough or porous concrete may need primer before installation. Steel, aluminum, and metal platforms should be degreased carefully because even a thin oil film can weaken adhesive contact. After placement, the tape should be pressed across the full width with firm roller pressure, especially at edges and corners. For dusty workshops, loading areas, or steel platforms exposed to cleaning cycles, testing a sample on the actual surface is recommended before wider installation
FAQ
Q1: Is this tape suitable for industrial floors instead of home stairs?
Yes. It is made for factory floors, workshops, warehouse walkways, metal platforms, loading areas, and other work areas where daily footwear traffic and surface contamination can reduce grip.
Q2: Can it bond to concrete and steel surfaces?
Yes. The surface must be dry, clean, stable, and free from oil, dust, rust, loose coating, or concrete powder. Porous concrete may need primer before application.
Q3: Is it the same as floor marking tape?
No. Floor marking tape is mainly used for visual guidance. This product focuses on traction, abrasion resistance, adhesive bonding, and grip under industrial footwear traffic.
Q4: Can Caution Roll Company make custom sizes?
Yes. As a manufacturer, Caution Roll Company can produce custom widths, lengths, colors, die-cut pieces, and roll formats for factory, workshop, platform, and warehouse use.