Clear Non Skid Deck Tape

Clear Non Skid Deck Tape Size: 25mm, 50mm, 100mm, 150mm widths, custom slitting available Color: Clear / transparent Material: Transparent PVC or PET film with textured traction surface Adhesive: Weather-resistant acrylic pressure-sensitive adhesive Thickness: Typical factory test range 0.60mm-0.90mm Use: Outdoor decks, docks, boat decks, sealed wood, fiberglass, painted aluminum Contact Us

Product Description

Caution Roll Company is a manufacturer of clear non skid deck tape for outdoor deck, dock, and boat deck areas where grip is needed but the original surface should still be seen. This transparent anti-slip roll is made for sealed wood, fiberglass, and painted aluminum surfaces exposed to wet shoes, rain splash, freshwater spray, UV, and short-term salt mist conditions. With a weather-resistant acrylic adhesive and a typical 0.60mm-0.90mm total thickness range, it is best applied to clean, dry surfaces with edge sealing in exposed wash-down areas.

Product Photos

Technical Data Sheet

Application

1. Wood deck walking paths where extra grip is needed without hiding the deck finish.
2. Dock walkways and boarding zones requiring non skid tape for docks under wet-shoe traffic.
3. Fiberglass boat deck panels where fiberglass deck anti slip tape should add traction without covering the surface color.
4. Painted aluminum gangways, marine access plates, and service platforms requiring aluminum deck safety grip tape.
5. Hatch edges, helm-side standing zones, boarding steps, and outdoor maintenance paths exposed to freshwater spray, deck washing, or short-term salt mist.

Product Overview

This clear non skid deck tape is designed as a transparent outdoor deck traction tape for exterior walking areas where a colored safety strip would look too heavy or industrial. It helps add grip to wood deck boards, dock walkways, fiberglass boat deck panels, painted aluminum access plates, and boarding zones while keeping the surface finish visible.

For outdoor projects, bonding performance depends heavily on surface preparation. The deck surface should be smooth, dry, degreased, and free from wax, salt residue, loose coating, old cleaner film, or powdering wood fibers. On sealed timber, fiberglass, and painted aluminum, a small sample bonding test is recommended before bulk use. This is especially important when the area is exposed to deck wash, freshwater spray, strong sunlight, or marine-adjacent salt mist.

In typical factory peel reference testing, the acrylic adhesive can reach about 12-18 N/25mm on stainless steel after 24 h. Actual performance on a deck, dock, or boat surface can vary with coating type, cleaning quality, temperature, water exposure, and edge protection.

Benefits

• Helps improve wet-shoe grip on outdoor deck paths, dock edges, boarding areas, and boat deck standing zones.
• Works as clear boat deck grip tape while allowing wood grain, fiberglass color, or painted aluminum finish to remain visible.
• Weather-resistant acrylic adhesive supports outdoor use when applied to a clean, dry, well-pressed surface.
• Typical holding power can be tested above 24 h under standard indoor test conditions, while outdoor areas should allow 24-48 h curing before wet exposure.
• Rounded corners help reduce corner lifting around hatch edges, gangways, and deck strips exposed to regular cleaning.
• Edge sealing is recommended for drainage edges, dock walkways, boat deck wash areas, and exposed outdoor locations.
• Roll width can be selected by location: narrow strips for hatch edges, medium width for dock walkways, and wider rolls for maintenance paths.

What Should Be Checked Before Applying Tape to Outdoor Deck Surfaces?

Before installation, check the deck for moisture, oil, wax, salt residue, loose paint, old cleaning chemical film, and uneven coating. Sealed or painted wood normally gives better adhesive contact than raw damp timber. Fiberglass and painted aluminum should be fully degreased because oxidation, marine cleaners, and coating differences can reduce adhesive contact. In sample observation, strips applied to cleaned, dried, firmly pressed surfaces and left to cure before wet exposure showed better edge stability than strips applied to damp or contaminated panels.

Production and Warehouse

Production Process

How Should Clear Non Skid Deck Tape Be Positioned on Decks, Docks, and Boat Decks?

The tape should follow real walking routes, not only decorative lines. On dock walkways, strips are usually placed across the main footstep direction while leaving drainage gaps open. On boat decks, it can be applied near boarding points, hatch edges, helm-side standing areas, fiberglass access panels, and aluminum gangways. In exposed areas, rounded corners, firm rolling pressure, and edge sealing help reduce water entry and early lifting after deck wash or outdoor cleaning. Wider rolls fit maintenance paths, while narrow strips are easier to place around hatch covers, board edges, and access plates.

FAQ

Can clear non skid deck tape be used on wood decks?

Yes. It is more suitable for sealed or painted wood decks than raw, damp, or powdering timber. The surface should be cleaned and dried before application.

Is it suitable for fiberglass boat decks?

Yes. Fiberglass surfaces should be cleaned, dried, degreased, and tested with a small sample before bulk installation.

Can it be used near saltwater areas?

It can be used in salt mist or marine-adjacent conditions, but it should not be treated as a long-term seawater immersion material.

Should the edges be sealed outdoors?

Yes. Edge sealing is recommended for exposed dock edges, boat deck wash areas, drainage zones, and frequently cleaned outdoor surfaces.